The Basics of Cutting and Grinding discs

[qhhdu233]

Abrasive-cutting processes are widely used to obtain semi-finished products from metal bars, slabs, or tubes. Thus, the abrasive cutting-off process is applied when requiring precision cutting and productivity at a moderate price. Cut-off tools are

You do not have permission to view link Войдите или зарегистрируйтесь.

s composed of small abrasive particles embedded in a bonding material, called the binder. This work aims to compare the cutting performance of

You do not have permission to view link Войдите или зарегистрируйтесь.

s with different composition, in dry cutting of steel bars. To do that, disc wear was measured and disc final topography was digitalized in order to determine both disc surface wear patterns and if the abrasive particles bonding into the binder matrix was affected. In addition, X-Ray inspection gave information about the abrasive grit-binder bonding. Therefore, the method here presented allows identifying discs with a superior abrasive-cutting capability, by combining profilometry and tomography to define micrometrical aspects, grit size, and binder matrix structure. Results led to the conclusion that discs with high grit size and protrusion, high grit retention by bond material, and closer mesh of fiberglass matrix binder were the optimal solution.

Plenty of manual cutting applications call for a hand-held grinder and cutting wheel. Cutting sheet metal, sizing a piece for fabrication, cutting out a weld to refabricate it, and cutting and notching in pipeline work are just a few examples of what can be accomplished using a grinder and cutting wheel.

Resinoid-bonded cutting wheels are a popular choice to achieve these types of cuts because they offer portability and allow you to cut in many different angles and orientations. The bonding agent, in this case resinoid, holds the wheel together so it can cut effectively. The bond wears away as the abrasive grains wear and are expelled so new sharp grains are exposed.

By following a few best practices, you can extend wheel life, promote safety, and improve productivity and efficiency within the process.

The Basics of Cutting Wheels
The main considerations in using resinoid-bonded wheels include the cutting application, the tool being used—such as a right-angle grinder, die grinder, or chop saw—desired cutting action, the material being cut, and space. Wheels typically provide a fast cutting action, long life, and tend to be cost-effective.

The two main types of resinoid-bonded abrasive cutting wheels are Type 1, which are flat, and Type 27, which have a raised hub. Type 1 wheels generally are used for straight-on cutting on electric or pneumatic right-angle grinders or die grinders and chop saws, among other tools. Type 27 wheels are required when there is some type of interference and the

You do not have permission to view link Войдите или зарегистрируйтесь.

needs to be raised up from the base of the grinder, but personal preference also plays a role in the decision. They are most commonly used with electric or pneumatic right-angle grinders.


Thin wheels, such as

You do not have permission to view link Войдите или зарегистрируйтесь.

, on the other hand, tend to remove less metal during the cut and have shorter life spans, but provide a quicker cut. There are some exceptions to this as different versions of thin wheels are lasting longer, so be sure to do your research before you make a final decision to ensure the wheel you select maximizes efficiency.

Specialty cutting wheels are also available that are designed for use with certain materials, such as stainless steel and aluminum.

Proper Positioning and Other Tips
In addition to paying attention to designations for RPM rating, size, and material, you should also follow these tips when using resinoid-bonded abrasive cutting wheels.

• Use the cutting wheel at a 90-degree angle, perpendicular to the work surface.
• Apply the proper amount of pressure—not too much, not too little—to allow the cutting wheel to do the work. Always avoid pushing too hard on the wheel, which can cause the grinder to stall or kick back or give you a much less efficient cutting action. It also increases the chances that you will slip or lose control of the tool, which can cause damage or injury.
• Choose a grinder with the highest torque or amperage available for the application, as this will help the wheel to do more of the work. For example, instead of using a 4.5-in.
  You do not have permission to view link Войдите или зарегистрируйтесь.
  on a 6-amp grinder, use a 4.5-in. wheel on a 10-amp grinder. The RPM rating remains the same, but the tool will provide more torque to cut into the metal.
• Choose a tool and consumables that offer quick, consistent cutting, which typically provides the most efficient performance.
• Remember, the thinner the cutting wheel, the more susceptible it can be to side loading, which is a term that describes when the wheel bends while moving side to side in the cut. This can turn dangerous if you lean too hard on a wheel, which can cause the wheel to break or jam in the cut. It can also reduce the efficiency of the wheel and increase the cut time.
• Store the wheel in a clean, dry environment, and avoid placing it in water or mud. This helps minimize environmental effects that could degrade its performance or cause it to crack or wear prematurely. The performance of resinoid bond tends to deteriorate when the wheel is stored for extended periods of time, so be sure to use FIFO (first in, first out) when using wheels.
• Inspect the wheel and consumable before each use to check for signs of damage or wear. Cutting wheels, including
  You do not have permission to view link Войдите или зарегистрируйтесь.
  can become harder to control as they wear down. If you can no longer make a safe cut because the wheel’s diameter is worn so thin, then the best course of action is to replace it.

A

You do not have permission to view link Войдите или зарегистрируйтесь.

c is defined by the type of abrasive material, bonding material, grain size, structure of the wheel, and grade of the wheel used for the machining of a component. These factors decide the grinding efficiency of the

You do not have permission to view link Войдите или зарегистрируйтесь.

and surface finish quality of the machined component. A wide range of abrasives are being used in modern era to overcome necessities in machining of various make of components. Abrasives ranging from the economic verses of aluminium oxide to the likes of super-abrasives such as cubic boron nitride and the expensive diamond grains are used for machining as well as surfacing purposes. Over the years, research has depicted that no distinct abrasive material can meet all the requirements of grinding applications. The mechanical and physical properties of a particular abrasive material make it suitable for a certain application.