A review on RO membrane technology: Developments and challenges

#1
A review on RO membrane technology: Developments and challenges
Reverse osmosis (RO) based desalination is one of the most important and widely recognized technologies for production of fresh water from saline water. Since its conception and initiation, a significant development has been witnessed in this technology w.r.t. materials, synthesis techniques, modification and modules over the last few decades. The working of a RO plant inclusive of the pretreatment and post-treatment procedures has been briefly discussed in the article. The main objective of this review is to highlight the historical milestones achieved in RO technology in terms of membrane performance, the developments seen over the last few years and the challenges perceived.

The material properties of the membrane dominate the performance of a RO process. The emergence of nano-technology and biomimetic
You do not have permission to view link Войдите или зарегистрируйтесь.
as the futuristic tools is capable of revolutionizing the entire RO process. Hence the development of nano-structured membranes involving thin film nano-composite membranes, carbon-nanotube membranes and aquaporin-based membranes has been focussed in detail. The problems associated with a RO process such as scaling, brine disposal and boron removal are briefed and the measures adopted to address the same have been discussed.

In response to the escalating world water demand and aiming to promote equal opportunities, reverse osmosis desalination has been widely implemented. Desalination is however constantly subjected to fouling and scaling which increase the cost of desalination by increasing the differential pressure of the membrane and reducing the permeate flux. A bench-scale desalination equipment has been used in this research to investigate the mitigation of fouling and scaling. This study involved the performance of membrane autopsy for fouling characterisation with special attention to flux decline due to sulphate precipitation and biofouling. Visual inspection, scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR) and microbiology tests (API) were performed. Results obtained showed the presence of diatoms, pseudomonas and polysaccharides as the main foulants causing biofouling. Analysis revealed sulphate deposits as well as aluminium, calcium and silica as the main elements contributing to inorganic scaling. Findings pointed out that the pre-treatment system of the small-scale reverse osmosis water treatment was inefficient and that selection of pre-treatment chemicals should be based on its compatibility with the membrane structure. The importance of characterisation for the verification of fouling mechanisms is emphasised.

This research was conducted to determine the performance of Reverse Osmosis (RO) membranes in producing pure water, pure water known as mineral-free water or water with zero dissolved solids (TDS = 0 ppm).PDAM (Regional Drinking Water Company) Tirta Musi in Palembang, South Sumatra and water from the Micro Filtration (MF) and Ultrafiltration (UF) processes are fed to the RO process using two feeding methods, namely a single pass and a circulation feed. In a single pass feed, the operating pressure is set at 20 - 50 Psig, where an increase in the product rate and the rejection rate so that the flux increases. Rejection of TDS obtained increased from 96.6% - 97.5%. Furthermore, the circulating feed system with a constant pressure of 50 Psig decreases TDS and Conductivity. Rejection of TDS 96.1% for PDAM water feed and Rejection of TDS for feed water from MF&UF 97.3% in subsequent feedings there was a decrease in TDS and conductivity but not significantly. The purified water produced has a TDS content of 0.16 - 0.48 ppm, a conductivity of 0.17 - 0.49 μs/cm, a pH of 6.99 - 7.2 and a resistivity of 177 - 185 kΩ, the characteristics of this pure water are according to the standard pure water in ASTM D1193 - 99e1 and NCCLS.
Clean water obtained by desalinating sea water or by purifying wastewater, constitutes a major technological objective in the so-called water century. In this work, a high-performance reverse osmosis (RO) composite thin membrane using multi-walled carbon nanotubes (MWCNT) and aromatic polyamide (PA), was successfully prepared by interfacial polymerization. The effect of MWCNT on the chlorine resistance, antifouling and desalination performances of the nanocomposite membranes were studied. We found that a suitable amount of MWCNT in PA, 15.5 wt.%, not only improves the membrane performance in terms of flow and antifouling, but also inhibits the chlorine degradation on these membranes. Therefore, the present results clearly establish a solid foundation towards more efficient large-scale water desalination and other water treatment processes.

Introduction
The availability of clean water has become a global problem because of the continuously increasing costs of energy and increasing scarcity of water resources1. This problem has been exacerbated in recent years in the so-called century of water. By far, the
You do not have permission to view link Войдите или зарегистрируйтесь.
process persists as the most reliable and cost-effective water desalination technique and numerous large-scale RO plants have been constructed around the world2,3. A wide range of polymers have shown potential for fabricating desalination membranes to be used in RO4. However, PA-based membranes tend to exhibit the best performance in terms of selectivity, flow, chemical stability and ease of large-scale fabrication. PA membrane technology was developed in the mid-70 s and has become the commercial benchmark in RO membranes5. In order to improve the membrane performances, the recent trend in polymer-based membrane research has been to investigate various types of nanocomposite films as an active layer of RO membrane, so-called nanocomposite membranes, in which these films are fabricated using a nanosized filler such as MWCNT, graphene, graphene oxide, silica, or zeolite6. In this regard, MWCNT·PA-based membranes have been prepared by several groups and in general, these membranes have exhibited some level of improved performance7,8,9,10,11,12. The advantages claimed for these membranes range from increased salt rejection, large fluxes, greater durability and even antimicrobial properties.
 
Сверху